Used Skinner 12" 4-Jaw Chuck with Top 2-Pc. Jaws 3" Thru Hole, Top 2-piece Jaws (Skinner Chuck # 21912-A8-62B)
View Enlarged Photos
Made in the USA!
Year:    
Serial No.
Email: Click Here to Email Us    
New Aloris Toolholders
View Enlarged Photos
"BLOW OUT" Prices!!!! While they Last!!!
Price: See Below
Year:     NEW
Serial No.
Email: Click Here to Email Us    

NEW ALORIS TOOLHOLDERS (Limited Quantities)
CA-6 Multiple Toolholder (1 available)...Reg. Price New $ 151.00... "SPECIAL" Price ONLY $ 85.00
CA-7 Universal Parting Blade Toolholder (4 available)...Reg. Price New $ 141.00... "SPECIAL" Price ONLY $ 80.00 ea.
CA-8
Threading Toolholder (2 available)...Reg. Price New $ 143.00... "SPECIAL" Price ONLY $ 80.00 ea.
CA-42
Boring Bar Holder (1 available)...Reg. Price New $ 220.00... "SPECIAL" Price ONLY $ 120.00
"Get 'em While they Last! When they're Gone......They're Gone!”
 

New "Take-Off" TAPER ATTACHMENT With 0 - 5" Taper/Ft. and 0 - 13 Degree Angle scales
***Current New Price from Acer is $ 850. (SAVE $ 300!)***
View Enlarged Photos
Removed from New ACER 1340G Lathe
Price: $ 550
Year:    
Serial No.
Email: Click Here to Email Us    
New "Demo" Edwards Coper Notcher (for 100 Ton Edwards Ironworkers)
View Enlarged Photos
Reg. Price $ 1,407 (f.o.b. Edwards in Minnesota)......SPECIAL PRICE Only $ 850 f.o.b. OKC, OK!
Price: $ 900
Year:    
Serial No.
Email: Click Here to Email Us    
New Pratt Burnerd Atlas 4" 4-Jaw Chuck
View Enlarged Photos
1"-8 Threaded Mount
Price: $ 80.00
Year:    
Serial No.
Email: Click Here to Email Us    
Used Troyke 18" Rotary Table
View Enlarged Photos
Price: $ 800
Year:    
Serial No.
Email: Click Here to Email Us    
Used Boye & Emmes Steady Rest  (From Boye & Emmes Manual Lathe ~28-32” Swing)  With Roller Tips,  ~9-1/2“ dia. capacity, Overall dimensions = ~28“ tall x ~24“ wide, Base Width = ~ 16-3/8“ wide, Approx. 15-1/4“ from outer edge of base to center of v-way groove.
View Enlarged Photos
From Boye & Emmes Lathe (Approx. 28 - 32" Swing)
Price: $ 750
Year:    
Serial No.
Email: Click Here to Email Us    
Used Scotchman 90 Degree V-Notcher

Used Notcher for Scotchman Ironworkers. Used on 65ton Ironworker Model 6509-24 (may fit other models).


View Enlarged Photos
Price: $ 650
Year:    
Serial No.
Email: Click Here to Email Us    
NEW HHT "Take-Off" 4-Jaw Chuck NEW “Take-Off” 20” 4-Jaw Chuck with Solid Jaws, ~ 6-1/4” Through Hole, D1-11 mount. This Chuck is unused and was removed from a new Summit Engine Lathe. Also Includes Chuck Wrench.
View Enlarged Photos
Unused - Removed from new Summit Lathe
Price: Call for Pricing
Year:    
Serial No.
Email: Click Here to Email Us    
Huge "LOT" of Collets / Tooling for Warner & Swasey Turret Lathes
View Enlarged Photos
(V-30269)
Price: $ 550
Year:    
Serial No.
Email: Click Here to Email Us    

Includes the following items:
Approx....... 40 each “Metric” ROUND 3-piece Collet “Sets,” 6 each “Inch” 3-piece Collet “Sets” (4 each ROUND - 2 each HEX), 9 each “Partial” Collet Sets, 3 each Eccentric Pusher Pads (part # 5200-1-3/8RNS .109 eccentric), 1 each hardinge 5/8” ROUND-serrated Collet and 9 each Large Collet “Holders” (SEE ADDITIONAL DESCRIPTIVE INFORMATION BELOW):
“INCH” 3-pc. Collet ''Sets''
Rounds - (1ea.) 7/8“, (1ea.) 1-1/2“, (1ea.) 1-3/8“, (1ea.) .461“?
Hex - (1ea.) 1“, (1ea.) 1/2“
“METRIC“ 3-pc. Collet "Sets" (All sizes are MM):
Rounds - (2ea.) 12, (2ea.) 13, (1ea.) 14, (2ea.) 15, (1ea.) 16, (2ea.) 18, (2ea.) 19, (1ea.) 20, (1ea.) 21, (2ea.) 22, (2ea.) 23, (2ea.) 24, (2ea.) 25, (1ea.) 26, (1ea.) 27, (2ea.) 28, (1ea.) 29, (1ea.) 30, (1ea.) 31, (1ea.) 32, (1ea.) 33, (2ea.) 34, (1ea.) 35, and (1ea.) 36MM
Hex - (1ea.) 17, (2ea.) 18, (1ea.) 19, (3ea.) 20, (1ea.) 21, (2ea.) 22, (1ea.) 23, (1ea.) 24, (1ea.) 25, (1ea.) 26, (1ea.) 27, (1ea.) 28, (2ea.) 30, and (1ea.) 32MM
COLLET HOLDERS (approx. 4-3/4“ OAL) - (9ea.) Total:
(1ea.) 25MM Round, (1ea.) 37MM Round, (1ea.) 28MM Hex, (6ea.) Misc.
Please note: Quantities, descriptions, etc. as listed above are approximated. We have done our best to provide as complete and as accurate a listing on this tooling as possible, however, all information is subject to verification and should be confirmed by the buyer prior to purchase.


While great care is taken to accurately communicate specifications and information about the “used” and “demo” machines and accessories we offer, in order to minimize confusion and best communicate a machine’s or item’s condition and specifications, a personal visual and mechanical inspection by the Buyer is highly recommended prior to purchase.

Lathes |  Mills |  Drills |  CNC Machines |  Brakes |  Iron Workers |  Misc.
Shears |  Tooling & Accessories |  Saws |  Grinders |  Rolls |  ... and MORE!

Page 1 of 1    <<Prev   Next>>
 
Login |